Air set 500W

Air system

1. Balboa Genesis Compressor for spa 500W
   Inner diameter for sealing: 32 mm
   Wide range of the Genesis products allows to find ideal ventilator for appropriate application.

   
   Features

   • Electronic and pneumatic models
   • Outstanding output
   • Massage mode „pulsing effect“
   • It is recommended for speed regulation
   • Quiet operation
   • Directional drainage inlet
   • Varying speed operated by „integrated electronics“
     
     
2. Whirpool Air Jet AIR JET – 44 mm/ 1,75" (With inlets) 6×
   Whirpool air jet AIR JET NEW of the brand Rising Dragon.Complete package including jet body.
   
   
   • Producer: Rising Dragon
   • Jet diameter: 43 mm
   • Type: Air
   • Material: Stainless
     
     
3. LX Hose PVC – flexi – diameter 13 mm 10×
   Hose for mains of air jets, Air MicroSilk and water jets.
   • Inner diameter: 9 mm
   • Outer diameter: 13 mm
     
     
4. Safety float (CHECK VALVE CG AIR)
   This safety equipment prevents water back-flow into the compressor.

   Safety equipment

   This compact valve is specifically designed to provide another level of safety for installation done by loop Hartford.

   It only opens to allow air-blow through jets during compressor? s operation and it closes once the compressor turns off. So, it prevents backflow of water into a ventilator.
   
   

5. Water Divertor – 12 × 10 mm
   Water divertor for spas and whirlpools. It is used for water access to jets from a water pump.

   • The reduction in the picture from 48mm to 40mm is not part of the package, if needed it must be purchased separately.
   • The plug with the outlet for the hose is part of the package.
     
     Exit: 12 x Ø 11 mm
     Inlet: 1× Ø 48 mm (outer), 1× Ø 48 mm (inner)
     
     
6. Connection pipe for circulation pumps and blowers diameter 48mm – 1m 3×
   Hard connection pipe.
   • Inner diameter: 43 mm
   • Outer diameter: 48 mm
     
     
7. Elbow piece – Plastic 90° inner diameter 48mm 5×
   Elbow piece has on both sides an inner opening for glueing 48 mm. Before glueing it is necessary to clean all connecting lines. Apply a thin layer of glue to the elbow piece and a tube and push the connecting lines together. Leave 5 minutes without movement. After proceed with glueing of other parts.
   • Entries: Glueing/Glueing
   • Entry diameter (inner): 48 mm
     
     
8. Elbow piece 45° (Diameter 48mm) 3×
   Elbow piece has on both sides inner hole for pasting of diameter 48 mm. Before pasting it is necessary to clean all seams. On the elbow piece and a hose apply a thin layer of glue and use pressure to put two parts together. Leave for 5 min without any action. Then you may continue with other pasting.
   • Entry: Pasting
   • Diameter of holes (inner): 48mm
     
     
9. Glue Weld-On 1 kg
   Premium highly resistant glue for the whirlpools, pools, watering systems and other plumbing piping.
   
   

   Glue Weld-On® 721 ™ is special quick-drying glue of blue colour with strong fixity. For glueing solid PVC piping SCH 40 up to diameter 160 mm and SCH 80 of diameter 110 mm. Suitable to be used as one-component glue without additives for glueing PVC piping and SDR tubes with pressure water flow in pools, whirlpools and watering systems (golf course, gardens and agriculture areas).

   Glue is ideal to be used with pressure systems for drinking water, watering systems and industrial piping. It is environmental friendly, safe in contact with drinking water, with low emissions and low odour, meeting the stricktest regulations.
   
   WARNING: The discount cannot be combined with other discounts! The highest possible discount will always be used in the order.